Hardware Contents
Package Contents
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-UST1716WT
For Style UST1716WT
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
May2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
B
Shade with Sockets
x1
AA
Crossbar Assembly
x1
A
Ceiling
Canopy
x1
E
Check Ring
x1
Spacer Tube
x1
H
Figure 1
A
STEP 1 Assemble the Ceiling Canopy,
Spacer Tube and Shade with
Sockets
-
A. Thread one end of the Nipple with Hex Nuts
(G) into the Hex Coupling on the top center of
the Shade with Sockets (H). By using pliers,
thread one Hex Nut against the hex coupling
and hand tighten until snug.
B. Place the Spacer Tube (F), the Check Ring
(E), the Ceiling Canopy (D), the Flat Washer
F
D
Edison Bulb
x3
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the
Crossbar Assembly (AA). Attach the
Crossbar Assembly (AA) to the Outlet
Box with the head of the Green
Ground Screw facing you. Secure it
with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires
with Ground Wire
AA
Outlet Box Screws
(not included)
Outlet
Box
Figure 2
STEP 3 Fit Ceiling Canopy to Crossbar Assembly-
A.
Ceiling Canopy A to the
Ceiling Canopy A
ceiling
Remove mounting balls from the Crossbar Assembly (AA). Fit the
( ) Crossbar Assembly (AA) and secure with
mounting balls. Note: The ( ) should be snug
against the and the mounting balls. If not, adjust the length of
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers,wire cutters, wirestrippers, electricaltape,
safetyglasses.
BulbRecommended:
EstimatedAssemblyTime:
Preparation:
(3)Medium BaseDecorative Filament 60W(supplied), Maximum100W,Alternatebulb(3)
13WCFL
30-45minutes
Identifyand inspectall parts beforebeginning installation.Check package contentlist anddiagrams
belowto besure all partsare present.If any partsare missingor damaged,donot attemptto assemble,install,or
operatethe fixture.Contact customer servicefor replacementparts.
Lock Washer
x1
Hex Nut
x1
G
Nipple with
Hex Nuts
x1
I
B
C
E
F
G
H
(C) and the Lock Washer (B) over
the top end of the Nipple (G) in
turn. Secure them with the Hex Nut
(A) and hand tighten until snug.
Mounting Screw
Hex Nut and
Lock Washer
A
AA
Mounting Ball
Figure 3
the nipple on the Crossbar
Assembly (AA) by unscrewing
the preassembled hex nut and
lock washer and then screwing
the mounting screws in or out
of the crossbar until the correct
length is achieved. Once the
Ceiling Canopy (A) is secure,
remove the mounting ball and
Ceiling Canopy (A) and
proceed to Step 4.
STEP 4 Wire Connections-
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed Side Wire
from fixture. Connect Black (or Red) Supply Wire from the Outlet
Box to Smooth Side Wire from Fixture. Connect Ground Wire from
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Figure 5
C
Flat Washer
x1
D
(5 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels